Convert-Me.Com - online units conversion
Instant conversion pages: weight, length, volume, weight to volume, area, cooking, pressure, more...
Converting US mesh size to Micron
Forum rules
Dear convert-me.com forum visitors,
Our forum has been available for many years. In September 2014 we decided to switch it to read-only mode. Month after month we saw less posts with questions and answers from real people and more spam posts. We were spending more and more resources cleaning the spam until there were less them 1 legitimate message per 100 spam posts. Then we decided it's time to stop.
All the posts in the forum will be available and searchable. We understand there are a lot of useful information and we aren't going to remove anything. As for the new questions, you can always ask them on convert-me.com FaceBook page
Thank you for being with us and sorry for any inconveniences this could caused.
Dear convert-me.com forum visitors,
Our forum has been available for many years. In September 2014 we decided to switch it to read-only mode. Month after month we saw less posts with questions and answers from real people and more spam posts. We were spending more and more resources cleaning the spam until there were less them 1 legitimate message per 100 spam posts. Then we decided it's time to stop.
All the posts in the forum will be available and searchable. We understand there are a lot of useful information and we aren't going to remove anything. As for the new questions, you can always ask them on convert-me.com FaceBook page
Thank you for being with us and sorry for any inconveniences this could caused.
8 posts
• Page 1 of 1
Converting US mesh size to Micron
by lost in aperture » Mon Sep 26, 2005 10:18 pm
:? How do I convert from US mesh size to Micron. Is there a formula?
- lost in aperture
Re: Converting US mesh size to Micron
by Ken Chevy » Mon Sep 26, 2005 11:03 pm
lost in aperture wrote::? How do I convert from US mesh size to Micron. Is there a formula?
I don't know what the formula would be but here are some conversions:
http://www.reade.com/Sieve/grit_conversion.html
Looks like mesh is pretty large holes.
- Ken Chevy
- competent
- Posts: 57
- Joined: Mon Sep 26, 2005 11:22 am
- Location: Salem, OR, USA
Re: Converting US mesh size to Micron
by Tunnelfrank » Thu Mar 09, 2006 1:28 am
Ken Chevy wrote:lost in aperture wrote::? How do I convert from US mesh size to Micron. Is there a formula?
I don't know what the formula would be but here are some conversions:
http://www.reade.com/Sieve/grit_conversion.html
Looks like mesh is pretty large holes.
You find a online tool for the conversion under: http://www.intertunnel.de/e_news_downloads_01.htm
Regards
FS
- Tunnelfrank
Re: Converting US mesh size to Micron
by Gerrit » Tue Aug 21, 2007 8:38 pm
It is good I now have some hold on the subject, but the above links give different results so it does not make things clearer for me.
- Gerrit
Re: Converting US mesh size to Micron
by dr2007@rediffmai.com » Mon Oct 20, 2008 7:25 pm
Convert 26 mesh (net) in to microns
- dr2007@rediffmai.com
Mesh Size
by Pedroski » Fri Dec 05, 2008 9:35 pm
Mesh size is the number of openings per linear inch. To convert to microns you also need to know the wire thickness of the mesh (in microns).
The formula would be:
Mesh opening in Microns = (254/mesh size) - (mesh size x wire diameter in microns)
The formula would be:
Mesh opening in Microns = (254/mesh size) - (mesh size x wire diameter in microns)
- Pedroski
by dkirk » Sat Dec 13, 2008 2:57 pm
I created a formula that has pretty good accuracy for the conversion of mesh to microns and vice-versa.
The formula is as follows, and it has reasonable accuracy from 45 to 400 mesh.
microns = 15000/mesh and this can also be written as mesh = 15000/microns.
You can find my recent article on this subject in the December 2008 issue of Powder and Bulk Engineer (the article is available online for free).
Don
The formula is as follows, and it has reasonable accuracy from 45 to 400 mesh.
microns = 15000/mesh and this can also be written as mesh = 15000/microns.
You can find my recent article on this subject in the December 2008 issue of Powder and Bulk Engineer (the article is available online for free).
Don
- dkirk
More info
8 posts
• Page 1 of 1